Sls 3d printing problems and solutions

SLS 3D Printing Issues and Options

Sls 3d printing problems and solutions


JawsTec operates with a number of innovative kinds of industrial nylon 3D printers. Two HP MJF 4210, an EOS P 396, and two EOS P 400’s. On this article issues and options will probably be mentioned based mostly on the SLS nylon powder printer (the EOS P collection). Steadily requested questions will probably be addressed on client and producer based mostly issues with the SLS course of.

If you want to order a print of SLS or MJF please go to JawsTec for all of your 3D printing wants at:

SLS 3D Printing Issues and Options

Frequent Client Questions

SLS means selective laser sintering. A laser melts collectively layers of powder to create the half in a mattress of powder, freed from helps and floor points the place helps would join. SLS printing is often completed with 120 microlayers. This gives the very best quality components with the best dimensional accuracy with out inflicting a construct to fail. SLS creates white components that may be dyed for the specified look.

How do I design for SLS 3D printing?

Designing for SLS may be very simple. As a result of the components are in-built a mattress of powder no thought has to enter helps and the design doesn’t need to have chamfers for injection molding. Partitions are really useful to be at least 1mm. Nylon 3D printed components are extra versatile so with small partitions the components can snap. All nylon components are often stronger than any FDM or SLA printers.

SLS 3D Printing Issues and Options

What tolerances can SLS 3D printing obtain?

Tolerances rely on the fabric getting used within the SLS construct. A typical tolerance for SLS printing is +-Zero.1mm. For any partitions or connectors, all edges of the wall ought to have room for +-Zero.1mm variance. Meaning, if a lid has to suit round a field, all four partitions want room for this tolerance. EOS would suggest a minimum of Zero.4mm however this might be across the minimal measurement. For a gap, the tolerances are +-Zero.1mm as nicely. Holes and the connectors constructed and related after must have a minimum of +-Zero.2mm play.

What power qualities does SLS have?

Energy will depend on the fabric within the SLS construct. Nylon 12 holds a Tensile Energy of 52MPa within the x, y, and z-direction. It holds a Tensile Modulus of 1800MPa in x and y and 1750MPa within the z-direction.

SLS 3D Printing Issues and Options

What floor finishes will be achieved on SLS?

The floor end on SLS machines can differ. SLS floor is often rougher than SLA and a special sort than FDM. The end nearly looks like easy sandpaper. The end will be helped with some kinds of dyeing and blasting. 3D printed components may also be tumbled in plastic media to easy up. Oil sprucing and shot peening are additionally efficient methods to easy a component.

Does orientation matter on an SLS construct?

Orientation does matter on an SLS printer. The underside facet of the half often has softer edges and the highest of the half often has sharper angles. Essentially the most correct a part of the printer is the laser. So any element that is essential ought to be positioned within the z-direction in order that the laser determines the sting the perfect.

SLS 3D Printing Issues and Options

How scorching can the SLS 3D printed half face up to?

The warmth an SLS half can deal with will depend on the fabric. Nylon 12 can stand heats as much as 163 levels Celsius earlier than getting tender. The Melting temperature is rated at 176 levels Celsius for the powder.

What supplies are supplied with the SLS 3D printer?

SLS has many supplies: Nylon 12, Nylon 11, Nylon 12 Glass-Stuffed, and Nylon 12 Carbon-Stuffed.

What’s the smallest wall that may be printed within the SLS?

The smallest wall that’s really useful by EOS for his or her SLS machines is 1mm in thickness. Partitions will be printed smaller, however they’re tougher to put up course of. If the half goes to be tumbled partitions ought to be a minimum of 2.5mm in thickness.

What’s the smallest gap that the SLS can print?

The smallest gap that may be printed and that may be cleared successfully is 1.5mm. If the outlet goes farther than 100mm the minimal will get elevated to 4mm to be cleared successfully.

What colours will be produced on the SLS printer?

SLS produces white components that may be dyed many colours. Black, crimson, blue, inexperienced, yellow, pink, purple, brown, and gray.

How do I get my half darkish black?

Dyeing components black will be difficult. The bottom of black is blue so the components can have a blue or purple tint to the black half. To get the components darker you’ll be able to shot peen or oil polish the components to get a darker shade.

Why is SLS onerous to paint?

SLS is the best out of the Nylon powder printers to paint. However dyeing in itself will be difficult. The components dye greatest in boiling water with skilled nylon Rit Dye.

Why are SLS colours higher than MJF?

With the white base, SLS components will be dyed a extra vibrant shade than MJF which has a black base.

Client Issues with SLS

Why is the floor end tough?

The floor end for SLS can have a rougher really feel as a result of small bits of powder get frivolously sintered to the sting of the half. With a laser printer, you at all times have some thermal bleed. The powder round your half will harden as a result of it’s near the warmth of half.

Why do the components really feel like sandpaper?

Thermal bleed makes SLS really feel a little bit tough originally. You possibly can fight this can tumbling, shot peening and oil sprucing.

How do I easy my SLS half?

You possibly can order your half pre smoothed from Jaws Tec within the type of tumbling, polished, or oil polished. You can too sand down your half with sandpaper for a smoother end.

How do I modify the colour of my SLS half?

SLS components will be dyed with boiling water and material dye. As soon as the half is dyed it’s that shade. You possibly can spray paint the components if the colour must be totally different. Ink-based sprays are additionally efficient in coloring a component.

Why does my half have floor defects?

Floor defects can seem throughout the construct course of. The half will be pulled by the recorder which causes some components of your half to appear like it has a progress.

How do I repair floor defects?

Floor defects will be sanded down if there’s a progress on the half. Typically the half will must be reprinted if the expansion is unhealthy sufficient. If there’s a gap within the half, it may be crammed in with some glue or wall spackling. If the outlet is just too deep although it’s best to reprint the half.

Why don’t my components match?

Tolerance points are often designed failers. Both the components weren’t designed for SLS printing or the tolerances are too tight.

How do I make my components match?

Components will be sanded down or items reduce off with a razor blade. When you consider the half will not be inside the tolerances, contacting the producer is one of the simplest ways to search out out what to do.

Why are my holes not clear?

Holes lower than 4mm diameter most definitely won’t clear within the sandblasting stage. They must be manually drilled out and something lower than 1mm will often be left to the shopper to drill.

Can I drill out my components?

Sure, you’ll be able to drill out any holes that aren’t clear or completely spherical.

Can I put inserts into my 3D printed half?

Sure, nylon components can have press inserts and heated inserts put in after they’ve been accomplished. Jaws Tec gives inserts should you contact them instantly and supply environment friendly data on what components want inserts.

Is my half designed for 3D printing?

Most components will be designed for 3D printing. With powder beds that basically opens up the probabilities for what will be completed. Skinny partitions or prongs gained’t come out wonderful however something above a 2mm wall thickness will probably be superb for post-processing.

Sure, SLS is of upper high quality with often higher floor end, temperature qualities, and power qualities.

Sure, SLS is of upper high quality. The floor end on SLA is healthier as a result of the layers are often thinner than 120 microns or 80 microns. SLA components are very fragile so they don’t seem to be as helpful as SLS, MJF, or FDM.

Each processes are very shut in high quality. SLS will be printed in white and is barely extra inflexible. This enables the components to be dyed shiny colours and the components will break sooner when pushed previous their restrict. SLS is barely porous so the printed components can’t maintain water nicely. MJF comes out a uncooked ash grey. This implies most MJF components are dyed black to maintain consistency. MJF components even have the next tensile power. MJF is denser than SLS so it could actually maintain water.


Sure, SLS and DMLS are the very same course of however SLS is for plastic powders and DMLS is for steel powders.

Credit score : Supply Hyperlink

Related posts